APPLICATIONS                            
   Aluminum                         Metal Buildings        
   Architectural Metals         Precast Panels
   Asphalt Shingles             PVC Trim Boards
   Brick & Masonry               Roof Flashing 
   Cedar & Redwood          Skylights  
   Copper                             Sun Rooms
   Cured Concrete               Termination Bars
   EIFS Systems                  Tile Roofing
   Fiber Cement Board        Vinyl Siding & Windows
   Glass & Fiber Glass       +More Building Materials
   Kynar Coatings
   (fluoropolymer coatings)
  
   COLORS                                       
 Clear, White, Black & over 200 NPC
 standard colors.
 • Mfg. name & color stamped on each plunger.
 Custom colors available in low
 minimum quantities.

 LIMITATIONS                               
   • Intended for exterior use. Interior application
     requires mandatory forced fresh air ventilation
     until aroma dissipates. Inform solvent odor
     sensitive persons this compound contains
     a petroleum solvent.

    • Not recommended for:
      Structural applications.
      Contact with expanded polystyrene
      Joints under constant water submersion.

INSTALLATION                              
Apply 3/8" deep, like diagram to a temperate, clean,
dry, frost free structurally sound surface that is free of
oils, soaps, silicone,  or loose material that may inhibit
bonding. Clean excess sealant with a solvent such as
xylene or by scraping. Warm tube overnight in cool
 weather.

Do not tool inside corner joints..
Tool control joints.
Back caulk butt joints.

Backer rod or bond breaker tape is required on butt
joints or control joints to prevent three point adhesion.
Do not apply when substrate temperature is above 125ºF
 
Prior to application, obtaining the building owners
approval of the sealant color is the applicator's
responsibility.

JOINT DESIGN PARAMETERS 
Maximum joint & sealant width is 3/4"
Maximum sealant depth is 1/2"
Minimum application depth is 3/8"
 

               PROPER INSIDE CORNER  CURED BEAD
     Consumer size, Approx. coverage =  14 Lin. Ft./tube
       Pro-Size, Approx. coverage = 26 Lin. Ft/tube

GENERAL INFORMATION           
 Shelf life:  1 Year @ 75°F
 Substrate application: 10ºF to 125°F
 Cured sealant temp. range:  -40ºF to 300°F
 Cure rate:  @ 75°F
     a) Thin skin in 24 hrs.
     b) Complete: 21 days @ 75°F

 Primerless: Paintable after skin forms.
 Stainable with solid color stains.
 No PCB's Used or Added.

CONSTRUCTION STANDARDS
Meets performance requirements of
TT-S-00230c, Class A, Type II  and ASTM
C-920, Type S, Grade NS, Class 25, Use
NT, except for weight loss.

LIMITED  WARRANTY
NPC warrants #900 Solar Seal will meet
the performance data tests listed below and
when judged according to the test methods
listed below. For best results on inside corner
joints the user must follow our installation
instructions and "Proper Cured Bead" diagram.
For other joint designs the user must test the
suitability prior to full application for his intended
use and assumes all risks. Buyer's sole remedy
shall be limited to the purchase price or
replacement of product exclusive of labor or cost
of labor. No other warranties implied or expressed
shall apply, including any warranty or fitness for
a particular purpose. NPC shall not be liable under
legal theory for special or consequential damage.
Expected life: 20+ years on inside corner joints
when installed as directed herein.

   • COMBUSTIBLE Do not use near heat or flame.
   • Contact NPC for written approval for use
      in food processing areas.
   • WARNING: This product contains chemicals
     known to the state of California to cause cancer 
     and/or reproductive harm.
 
 PACKAGING                                 
Consumer size tubes (10.3 oz), 12/case,
 PRO-SIZE tubes (19 oz),  9/case
      5  gallon pails
     55 gallon drums